กรณีต้องการติดต่อทาง LINE@ กรุณาเพิ่มเพื่อนด้วย LINE ID : @warf
Advertsement
Arduino Raspberry Pi Zigbee/802.15.4 Sensors Robotics LCDs

Basic SPDT Relay Carrier with 12VDC Relay

220.00 THB

ราคาดังกล่าวรวมภาษีมูค่าเพิ่ม 7% เรียบร้อยแล้ว

Facebook Share << คลิ๊ก Share
Part No. : ELE-WA060947721
Manufacture No. : #2482
จำนวนในสต็อก : 10
ต้องการสั่งซื้อจำนวน
OR
ชำระเงิน PayPal แบบใหม่
ช่วยให้คุณซื้อสินค้าได้รวดเร็วและง่ายยิ่งกว่าเดิม
เพิ่มเพื่อน

รายละเอียดสินค้า: Basic SPDT Relay Carrier with 12VDC Relay

The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. This item includes the basic carrier PCB with a soldered-in 12 V relay, 5.0 mm terminal blocks for the switch connections, and straight 0.1" male header for the control connections. The included relay is an Omron G5LE-14-DC12.

 

Overview

The Pololu basic relay carrier modules make it easy to control a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. The modules are available with 5 V and 12 V power relays—Omron G5LE-14-DC5 and G5LE-14-DC12 (1MB pdf), respectively—and they are available pre-soldered or as partial kits that allow greater application flexibility:

 

 

 

The carrier board is also available without the relay or connectors for those preferring to use their own relays that have the common “sugar cube” pinout and footprint.

 

The carrier board routes the three relay control pins to 0.1″-spaced pins compatible with standard solderless breadboads and female servo cable connectors. The assembled version of this board has a 0.1″ straight male header soldered to these pins while the partial kit version includes 8×1 straight and right angle 0.1″ male header strips that can optionally be broken into 3×1 pieces and soldered in. The relay switch pins are routed to a set of large pads intended for use with a 3-pin 5mm-pitch terminal block and a set of smaller pads with a 0.2″ pitch, making them compatible with 0.1″ perfboards. The assembled version of this board has a terminal block soldered to these pins while the partial kit version includes a 3-pin terminal block that can be optionally soldered in.

 

Pololu basic SPDT relay carrier with 5 VDC relay (partial kit).

Pololu basic SPDT relay carrier with 5 VDC relay (assembled).

 

Advantages over similar products

  - Compact layout

  - Two LEDs to indicate coil actuation

  - Zener diode for fast current decay on relay coil

  - Specification of electrical routing clearance rules on relay switch nodes

 

Using the relay module

 

 

 

The switch portion of the relay is accessible on one side of the board while the control pins are routed to the other. The relay coil is powered by supplying 5 V or 12 V across the VDD and GND pins (depending on the relay), and it is activated by a digital high control signal on the EN pin. The control signal is fed directly to a BSS138 N-channel MOSFET, which in turn actuates the relay coil when the control voltage exceeds approximately 2.5 V (see BSS138 datasheet (92k pdf) for details).

 

The relay switch terminals COM (common), NO (normally open), and NC (normally closed) are routed on the PCB with a minimum clearance of 60 mils (1.5 mm) from other copper. The copper traces are designed to be at least 45 mil (1.1 mm) from the board edges, though manufacturing variations in the board edges can make those distances slightly lower.

 

In most applications, the current and voltage ratings for the module will match the ratings of the relay used. Maximum current, maximum voltage, and life expectancy are interdependent; we therefore recommend careful examination of your relay’s datasheet.

 

Warning: This product is not designed to or certified for any particular high-voltage safety standard. Working with voltages above 30 V can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.

 

Schematic diagram

 

Schematic diagram for the Pololu basic SPDT relay carrier.

 

 

This schematic is also available as a downloadable pdf (131k pdf).

 

Dimensions
  - Size:  1″ × 1.2″ × 0.9″ 
  - Weight:  16 g 

 

General specifications
  - Voltage:  12 V 
  - Partial kit?:  N 

 

ไฟล์ดาวน์โหลด: Basic SPDT Relay Carrier with 12VDC Relay

downloads basic SPDT relay carrier schematic diagram : Download
downloads Omron G5LE single-pole 10A power relay datasheet : Download

ความคิดเห็นผู้ใช้งาน: Basic SPDT Relay Carrier with 12VDC Relay

แสดงความคิดเห็น:

เข้าสู่ระบบสมาชิก ก่อนแสดงความคิดเห็น.
ได้รับการรับรองธุรกิจพาณิชย์อิเล็กทรอนิคส์
mce-lab
How to pay
Cards We Accept เลขทะเบียนพาณิชย์อิเล็กทรอนิกส์