กรณีต้องการติดต่อทางไลน์กรุณาเพิ่มเพื่อนด้วยไลน์ ID : @warf
Advertsement
Arduino Raspberry Pi Zigbee/802.15.4 Sensors Robotics LCDs

ST VNH2SP30 30A Motor Driver

550.00 THB

ราคาดังกล่าวรวมภาษีมูค่าเพิ่ม 7% เรียบร้อยแล้ว

Facebook Share << คลิ๊ก Share
Part No. : ELE-WA451665240
Manufacture No. : VNH2SP30
จำนวนในสต็อก : 3
ต้องการสั่งซื้อจำนวน
OR
ชำระเงิน PayPal แบบใหม่
ช่วยให้คุณซื้อสินค้าได้รวดเร็วและง่ายยิ่งกว่าเดิม
เพิ่มเพื่อน

รายละเอียดสินค้า: ST VNH2SP30 30A Motor Driver

The VNH2SP30 is an improved version of the VNH3SP30 motor driver, featuring current sensing, increased drive capability, and a higher maximum PWM frequency of 20 kHz.

We use these motor drivers in several of our products, including the single and dual motor driver carrier boards, the SMC04 high-power motor controller w/feedback, the TReX motor controller, and the Orangutan X2 robot controller. We offer the chips by themselves for more direct integration into your project or product.

 

VNH3SP30 and VNH2SP30 Comparison


 

 

   VNH3SP30

VNH2SP30

Operating supply voltage (Vcc)

    5.5 – 36 V*           

5.5 – 16 V

Maximum current rating

    30 A

30 A

MOSFET on-resistance (per leg)

    34 mΩ

19 mΩ

Maximum PWM frequency

    10 kHz

20 kHz

Current sense

    none

approximately 0.13 V/A

Over-voltage shutoff

    36 V*

16 V minimum (19 V typical)

Time to overheat at 20 A**

    8 seconds

35 seconds

Time to overheat at 15 A**

    30 seconds

150 seconds

Current for infinite run time**

    9 A

14 A

 

 

*Manufacturer specification.In our experience, shoot-through currents make PWM operation impractical above 16 V. 

**Typical results using Pololu motor driver carrier with 100% duty cycle at room temperature.

 

Real-world power dissipation considerations

The motor drivers have maximum current ratings of 30 A continuous. However, the chips by themselves will overheat at lower currents (see table above for an example set of values). The actual current you can deliver will depend on how well you can keep the motor driver cool. Good air flow and a heat sink will allow the chip to operate at currents closer to its maximum rating without overheating.

Many motor controllers or speed controllers can have peak current ratings that are substantially higher than the continuous current rating; this is not the case with these motor drivers, which have a 30 A continuous rating and a over-current protection that can kick in as low as 30 A (45 A typical). Therefore, the stall current of your motor should not be more than 30 A. (Even if you expect to run at a much lower average current, the motor can still draw high currents when it is starting or if you use low duty cycle PWM to keep the average current down.)


Note: This motor driver IC comes in a MultiPowerSO-30 package that requires surface mounting; it is not a through-hole component. Our carrier boards give you convenient access to the VNH2SP30 and VNH3SP30 motor drivers without any surface-mount soldering.

 

Dimensions
    - Size:0.68" x 0.75"


General specifications
    - Motor driver:VNH2SP30
    - Motor channels:1
    - Minimum operating voltage:5.5 V
    - Maximum operating voltage:16 V
    - Continuous output current per channel:14 A1
    - Peak output current per channel:30 A
    - Maximum PWM frequency:20 kHz
    - MOSFET on-resistance (max per leg):19 mΩ
    - Package:MultiPowerSO-302
    - Reverse voltage protection?:N

 

Notes:

    - Typical results using the Pololu VNH2SP30 motor driver carrier with 100% duty cycle at room temperature.
    - This package requires surface mounting.

ไฟล์ดาวน์โหลด: ST VNH2SP30 30A Motor Driver

downloads VNH2SP30 motor driver data sheet : Download
downloads VNH3SP30 motor driver data sheet : Download

ความคิดเห็นผู้ใช้งาน: ST VNH2SP30 30A Motor Driver

แสดงความคิดเห็น:

เข้าสู่ระบบสมาชิก ก่อนแสดงความคิดเห็น.
ได้รับการรับรองธุรกิจพาณิชย์อิเล็กทรอนิคส์
mce-lab
How to pay
Cards We Accept เลขทะเบียนพาณิชย์อิเล็กทรอนิกส์