กรณีต้องการติดต่อทางไลน์กรุณาเพิ่มเพื่อนด้วยไลน์ ID : @warf
Advertsement
Arduino Raspberry Pi Zigbee/802.15.4 Sensors Robotics LCDs

RoboClaw 2x5A Motor Controller (V5)

3,600.00 THB

ราคาดังกล่าวรวมภาษีมูค่าเพิ่ม 7% เรียบร้อยแล้ว

Facebook Share << คลิ๊ก Share
Part No. : ELE-WA451657878
Manufacture No. : 2394
จำนวนในสต็อก : 2
ต้องการสั่งซื้อจำนวน
OR
ชำระเงิน PayPal แบบใหม่
ช่วยให้คุณซื้อสินค้าได้รวดเร็วและง่ายยิ่งกว่าเดิม
เพิ่มเพื่อน

รายละเอียดสินค้า: RoboClaw 2x5A Motor Controller (V5)

The RoboClaw motor controllers from Ion Motion Control (formally Orion Robotics) can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 5 A per channel (10 A peak).

 

Overview
The RoboClaw from Ion Motion Control (formerly Orion Robotics) is an efficient, versatile, dual-channel synchronous regenerative motor controller. It can supply two brushed DC motors with 5 A, 15 A, 30 A, or 60 A continuous (depending on the model) at voltages from 6 V to 34 V, and it allows for peak currents up to twice the maximum continuous rating.

 

The RoboClaw features dual quadrature decoding capability. A built-in PID routine can be used for closed-loop speed control, maintaining motor speeds even if the load varies, or the encoder counts and speeds can be read directly from the RoboClaw for use with an external control system. Analog feedback is also supported for closed-loop position control.

 

The RoboClaw has a USB interface that acts as a virtual serial (COM) port, allowing it to be controlled directly from a computer. Several other interface modes are supported by the RoboClaw as well: it can be controlled via TTL serial for use with an embedded system, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), or analog voltages for use with potentiometers or analog joysticks.

 

The RoboClaw 2x5A (V5), 2x15A (V5), and 2x30A (V5) have USB Micro-B connectors; the RoboClaw 2×60A (V4) has a USB Mini-B connector (as did older USB RoboClaws).

 

Key Features
  - Simple bidirectional control of two brushed DC motors
  - 6 V to 34 V operating supply range
  - 5 A to 60 A maximum continuous current output, depending on controller model
  - Automatic current limiting reduces duty cycle when motor current is between 1× and 2× the controller’s rated current
  - Four communication or control options:
    - USB serial interface (virtual COM port)
    - Logic-level (TTL) serial interface for direct connection to microcontrollers or other embedded controllers
    - Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller
    - 0 V to 2 V (5 V tolerant) analog voltage interface for direct connection to potentiometers and analog joysticks
  - Dual feedback inputs for PID closed-loop control:
    - Speed control with quadrature encoders, up to 19.6 million encoder pulses per second
    - Position control with analog encoders or potentiometers
    - (Open-loop control with no feedback also available)
  - Screw terminals for quick connect/disconnect
  - Configurable via pushbutton interface
  - Regenerative braking
  - Tolerates high-speed direction changes
  - Jumper-selectable 5 V BEC
  - Battery monitoring and under-voltage cutoff protects batteries from over-discharging

 

RoboClaw Comparison Table

 
2x5A

2x15A

2x30A

2x45A
ST 2x45A

2x60A
Motor channels: 2
Operating voltage: 6 V to 34 V
Continuous output current: 5 A 15 A 30 A 45 A 60 A
Peak output current: 10 A 30 A 60 A 60 A 120 A
5V BEC(1) max current: 150 mA 3 A
Width: 1.7″ (4.2 cm) 2.1″ (5.2 cm) 3.4″ (8.6 cm)
Length: 1.9″ (4.8 cm) 2.9″ (7.4 cm) 3.9″ (10 cm)
Weight: 17 g 60 g 60 g (2x45A)
63 g (ST 2x45A)
205 g

1 Battery Eliminator Circuit

Sample Code
Ion Motion Control has written an Arduino library for the RoboClaw that makes it easy to interface these motor controllers with an Arduino. The library comes with several example sketches that demonstrate different methods of controlling the RoboClaw.

 

Note: Ion Motion Control was formerly Orion Robotics, which was previously Basic Micro. Ion Motion Control uses the following product names and number for the RoboClaw controllers:

    “RoboClaw 2×5A Motor Controller”, Item Id: ION403
    “RoboClaw 2×15A Motor Controller”, Item Id: ION412
    “RoboClaw 2×30A Motor Controller”, Item Id: ION413
    “RoboClaw 2×60A Motor Controller”, Item Id: ION414

 

Dimensions
  - Size:1.7″ × 1.9″ × 0.7″
  - Weight:17 g

 

General specifications
  - Motor channels:2
  - Control interface:USB; non-inverted TTL serial (2-way); RC servo pulses; analog voltage1
  - Minimum operating voltage:6 V
  - Maximum operating voltage:34 V
  - Continuous output current per channel:5 A
  - Peak output current per channel:10 A

 

Notes: Available baud rates are 2400, 9600, 19,200, and 38,400 bps.

 

ไฟล์ดาวน์โหลด: RoboClaw 2x5A Motor Controller (V5)

downloads Manual : Download
downloads Drawing : Download

ความคิดเห็นผู้ใช้งาน: RoboClaw 2x5A Motor Controller (V5)

แสดงความคิดเห็น:

เข้าสู่ระบบสมาชิก ก่อนแสดงความคิดเห็น.
ได้รับการรับรองธุรกิจพาณิชย์อิเล็กทรอนิคส์
mce-lab
How to pay
Cards We Accept เลขทะเบียนพาณิชย์อิเล็กทรอนิกส์