ตัดแผ่น PCB ตามขนาดที่ต้องการทำ พร้อมทั้งทำความสะอาดผิวทองแดง Cut a PCB to your preferred size. The copper surface must be completely clean.
ทำการตัดแผ่น Dryfilm ตามขนาดแผ่น PCB ที่เตรียมไว้ Cut a piece of dry film with the size of your board.
ลอกแผ่นพลาสติก (Cover Sheet) ที่ติดอยู่กับแผ่น Dryfilm ด้านใด ด้านหนึ่งออก Strip off one of the cover sheets which are primitively adhered to the dry film.
นำ Dryfilm ไปติดกับแผ่น PCB ที่เตรียมไว้ (โดยระวังอย่าให้มีฟองอากาศ) Adhere the film to the PCB. (Be careful of bubbles!)
ใช้ผ้าวางทับบน PCB จากนั้นนำเตารีดไฟฟ้า ปรับความร้อน ปานกลาง หรือโดยประมาณ 110°C รีดทับบนแผ่นผ้าให้ทั่ว (ระวังอย่าให้ความร้อนสูงจนเกินไปเพราะ Dry Film จะละลายได้) Place a clean sheet ( a piece of cloth ) on top of the PCB and iron all over the sheet with approximately 110 degree Celsius heat. ( Be careful for excessive heat which could melt the film).
จากนั้นตรวจสอบดูว่า Dry Film ที่ติดบนแผ่น PCB มีฟองอากาศแทรกอยู่ หรือไม่ ถ้ามีให้นำเข็มที่มีปลายแหลมเจาะฟองอากาศแล้วไล่อากาศออก และให้ใช้เตารีดรีดทับอีกครั้งหนึ่ง (ฟองอากาศนี้ทำให้ Dry Film ไม่เกาะติดกับแผ่น PCB เป็นเหตุให้ลายเส้นที่จุดนี้ขาดได้) Check up the bonded dry film for bubbles. If there are any bubbles, pop the bubble with a pin and redo the previous step (step 5). The dry film will not be bonded to the PCB if there are any bubbles.
เมื่อได้แผ่น PCB ที่เคลือบ Dry Film เรียบร้อยแล้วนั่นคือที่จะขึ้นลายได้ ให้นำหลอดไฟฟ้า (หลอดไส้) ขนาด 100 วัตต์ แขวนไว้เหนือแผ่น PCB ห่างประมาณ 1 ฟุต Now your PCB is laminated. Place a 100 watts light bulb twelve inches high over the PCB.
นำแผ่นฟิล์มอาร์ทเวิร์คแบบ Negative ที่มีขนาดเท่าแนบทับบนแผ่น PCB แล้วนำกระจกใสมาวางทับอีกที เพื่อให้ฟิล์มอาร์ทเวิร์ค แนบติดกับแผ่น PCB แน่นขึ้นจากนั้นเปิดไฟให้กับหลอดไฟ เพื่อทำการถ่ายขึ้นลายใช้เวลาในการถ่ายประมาณ 15 นาที Place the artwork film on the PCB and put a clear glass on top so the weight of the glass makes the artwork and the PCB better adhered to each other. Illuminate the bulb for approximately 15 minutes.
ผสมน้ำยาล้าง Dry Film (Developer) โดยนำผง Developer ที่ให้มาผสมลงน้ำสะอาด 10 กรัมต่อ น้ำ 1 ลิตร. กวนให้ละลายจนหมด Mix the developer powder with 10g. of 1 liter clean water and stir them until the developer and the water completely mixed.
ลอกแผ่นพลาสติก (Cover Sheet) ที่ติดอยู่บนแผ่น Dry Film อีกชั้นหนึ่งออก Strip off the other cover sheet.
แล้วนำมาล้างในน้ำยา Developer ที่เตรียมไว้ แล้วใช้ฟองน้ำลูบไปมาให้ทั่วเพียงเบา ๆ Clean the PCB with the developer by using a sponge to gently rub all over the PCB until the artwork completely showed up. Make sure there is no any unwanted dry film left behind.
จนกระทั่งปรากฏลายเส้นของอาร์ทเวิร์คเด่นชัด ไม่มีส่วนของ Dry Film ที่ไม่ต้องการตกค้างอยู่ จากนั้นนำมาล้างน้ำให้สะอาด แล้วรอให้แห้ง Rinse the pcb with water and wait until it is dry.
เตรียมน้ำยากัด PCB ใส่ลงในภาชนะ จากนั้นใส่แผ่น PCB ลงไปเขย่าน้ำยาไปมาพร้อมทั้งตรวจสอบ กระทั่งทองแดงในส่วนที่ไม่ต้องการถูกกัดออกจนหมด จะได้ลายเส้นตามต้องการ แล้วนำไปล้างด้วยน้ำสะอาด Put the PCB into a bowl of PCB Etchant. Slowly shake the bowl until the excessive (unwanted) copper is completely etched. Rinse the PCB with clean water.
นำแผ่น PCB ที่ต้องการลอก Dry Film ออกแช่ลงในภาชนะ ที่ใส่ทินเนอร์ ทิ้งไว้สักครู่แผ่น Dry Film จะอ่อนตัวและละลายออกจากนั้น จึงนำไปทำความสะอาด Put the PCB into a bowl of thinner. The film will get soften and be peeled off from the PCB. Rinse the PCB with clean water.
เจาะแผ่น PCB แล้วทำความสะอาดให้เรียบร้อย ท่านก็จะได้แผ่น PCB ที่ต้องการ Drill the holes and clean up your new PCB.