กรณีต้องการติดต่อทางไลน์กรุณาเพิ่มเพื่อนด้วยไลน์ ID : @warf
Advertsement
Arduino Raspberry Pi Zigbee/802.15.4 Sensors Robotics LCDs

Dual VNH3SP30 Motor Driver Carrier MD03A

1,950.00 THB

ราคาดังกล่าวรวมภาษีมูค่าเพิ่ม 7% เรียบร้อยแล้ว

Facebook Share << คลิ๊ก Share
Part No. : ELE-WA451665230
Manufacture No. : 707
รอสินค้าประมาณ 1-2 สัปดาห์ หลังยืนยันสั่งซื้อ
ต้องการสั่งซื้อจำนวน
OR
ชำระเงิน PayPal แบบใหม่
ช่วยให้คุณซื้อสินค้าได้รวดเร็วและง่ายยิ่งกว่าเดิม
เพิ่มเพื่อน

รายละเอียดสินค้า: Dual VNH3SP30 Motor Driver Carrier MD03A

If you are looking to drive two high-power motors through one compact unit, these dual VNH3SP30 motor driver carriers are perfect for you. With these boards, it’s easy to get a medium-sized, differential drive robot running in no time. The VNH3 version is a lower-cost option than its VNH2 counterpart.


Overview

The Pololu dual high-power motor drivers are compact carriers for the VNH3SP30 and VNH2SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH2SP30 datasheet, including pull-up and current-limiting resistors and a FET for reverse battery protection. (The current sense circuit is populated on both versions of the board, but only the VNH2SP30 supports current sense.) To keep the number of I/O lines down, the two enable/diagnostic lines on each chip are tied together. All you need to add is a microcontroller or other control circuit to turn the H-Bridges on and off.

 

Please note that we offer several other products based on these same chips, including single carrier boards for controlling one motor, the qik 2s10v12 dual serial motor controller, the TReX motor controller, the jrk 12v12 USB motor controller with feedback, and the Orangutan X2 robot controller. We also have a family of higher-power motor drivers that can deliver more current over a wider operating voltage range.

 

In a typical application, the power connections are made on one end of the board, and the control connections are made on the other end. +5 volts must be supplied to the board through the smaller 0.1"-spaced pins; the input voltage is available at those pins as well, but the connection is not intended for currents exceeding a few amps. The diagnostic pins can be left disconnected if you do not want to monitor the fault conditions of the motor drivers. INA and INB control the direction of each motor, and the PWM pins turns the motors on or off. For the VNH2SP30 version, the current sense (CS) pins will output approximately 0.13 volts per amp of output current. If you want to add current sensing to the VNH3SP30 version, or if you want higher-accuracy current sensing with the VNH2SP30 version, please consider our ±30A ACS714 current sensor carrier.

 

The dual motor driver PCB includes provisions for installing up to three large capacitors to limit disturbances on the main power line. Two 10mm radial capacitors may be mounted between the motor driver ICs, and an axial capacitor may be mounted between the ICs and power connections. It is generally not necessary to use all three capacitors; two radial capacitors are included with each unit. For applications that require a low profile, a single capacitor can be installed on its side as shown in the picture to the right.

 

VNH3SP30 and VNH2SP30 Comparison

 

 

      VNH3SP30

VNH2SP30

Operating supply voltage (Vcc)

      5.5 – 36 V*                            

5.5 – 16 V

Maximum current rating

      30 A

30 A

MOSFET on-resistance (per leg) 

      34 mΩ

19 mΩ

Maximum PWM frequency

      10 kHz

20 kHz

Current sense

      none

approximately 0.13 V/A

Over-voltage shutoff

      36 V*

16 V minimum (19 V typical)

Time to overheat at 20 A**

      8 seconds

35 seconds

Time to overheat at 15 A**

      30 seconds

150 seconds

Current for infinite run time**

      9 A

14 A

 

*Manufacturer specification. In our experience, shoot-through currents make PWM operation impractical above 16 V.

**Typical results using Pololu motor driver carrier with 100% duty cycle at room temperature.


Real-world power dissipation considerations

The motor drivers have maximum current ratings of 30 A continuous. However, the chips by themselves will overheat at lower currents (see table above for typical values). The actual current you can deliver will depend on how well you can keep the motor drivers cool. The carrier printed circuit board is designed to draw heat out of the motor driver chips, but performance can be improved by adding a heat sink. In our tests, we were able to deliver short durations (on the order of milliseconds) of 30 A and several seconds of 20 A without overheating. At 6 A, the chip gets just barely noticeably warm to the touch. For high-current installations, the motor and power supply wires should also be soldered directly instead of going through the supplied terminal blocks, which are rated for up to 15 A.

Many motor controllers or speed controllers can have peak current ratings that are substantially higher than the continuous current rating; this is not the case with these motor drivers, which have a 30 A continuous rating and a over-current protection that can kick in as low as 30 A (45 A typical). Therefore, the stall current of your motor should not be more than 30 A. (Even if you expect to run at a much lower average current, the motor can still draw high currents when it is starting or if you use low duty cycle PWM to keep the average current down.)

 

Dimensions
    - Size:1.86" x 1.86"


General specifications
    - Motor driver:VNH3SP30
    - Motor channels:2
    - Minimum operating voltage:5.5 V
    - Maximum operating voltage:16 V1
    - Continuous output current per channel:9 A
    - Peak output current per channel:30 A
    - Continuous paralleled output current:15 A
    - Maximum PWM frequency:  10 kHz
    - Reverse voltage protection?:Y2


Notes:
    - The datasheet claims a maximum of 36 V, but shoot-through issues make operation impractical above 16 V.
    - There are unprotected electrolytic capacitors that will be damaged by reverse voltage.

 

ไฟล์ดาวน์โหลด: Dual VNH3SP30 Motor Driver Carrier MD03A

downloads VNH3SP30 motor driver data sheet : Download
downloads VNH2SP30 motor driver data sheet : Download
downloads IRFR3707Z MOSFET datasheet : Download
downloads STD60NF3LL MOSFET datasheet : Download

ความคิดเห็นผู้ใช้งาน: Dual VNH3SP30 Motor Driver Carrier MD03A

แสดงความคิดเห็น:

เข้าสู่ระบบสมาชิก ก่อนแสดงความคิดเห็น.
ได้รับการรับรองธุรกิจพาณิชย์อิเล็กทรอนิคส์
mce-lab
How to pay
Cards We Accept เลขทะเบียนพาณิชย์อิเล็กทรอนิกส์