วาร์ฟฯ ได้ผ่านการรับรอง จากกรมพัฒนาธุรกิจการค้า กระทรวงพาณิชย์
ว่าได้ผ่านการตรวจประเมินตามเกณฑ์มาตรฐานคุณภาพธุรกิจพาณิชย์อิเล็กทรอนิกส์ รายละเอียด
Advertsement
Advertsement

Dual MC33887 Motor Driver Carrier

1,450.00 THB

ราคาดังกล่าวรวมภาษีมูค่าเพิ่ม 7% เรียบร้อยแล้ว

(0 Comment)

Facebook Share << คลิ๊ก Share รับส่วนลด 2%
Part No. : ELE-WA451665236
Manufacture No. : 712
จำนวนในสต็อก : 0
รอสินค้าประมาณ 1-2 สัปดาห์ หลังยืนยันสั่งซื้อ
ต้องการสั่งซื้อจำนวน
OR
ชำระเงิน PayPal แบบใหม่
ช่วยให้คุณซื้อสินค้าได้รวดเร็วและง่ายยิ่งกว่าเดิม

รายละเอียดสินค้า: Dual MC33887 Motor Driver Carrier

If you are looking to drive two DC motors running from 5-28 V and drawing up to 5 A (2.5 continuous), this compact dual carrier of Freescale’s MC33887 motor driver is just what you need. Extra features such as current sensing and over-current protection make the 33887 an excellent general-purpose motor driver.

 

These compact dual carriers for the Freescale Semiconductor MC33887 motor driver integrated circuit are an easy way to connect two brushed DC motors running from 5 to 28 V and drawing up to 5 A (peak) each to your project. The board incorporates all of the components of the typical application diagram on page 25 of the MC33887 datasheet, plus motor-direction LEDs and a FET for reverse battery protection. All you need to add is a microcontroller or other control circuit to turn the H-Bridge on and off. For a single-motor version of this motor driver, please consider the MC33887 motor driver carrier. For a very similar motor driver that supports ultrasonic (up to 20 kHz) PWMs and a wider logic voltage range (3 – 5 V), please consider the MC33926 motor driver carrier or Dual MC33926 motor driver carrier.

 

In a typical application, the power connections are made on one end of the board, and the control connections (5V logic) are made on the other end. The enable (EN) pins do not have pull-up resistors, so you must pull them to +5 V in order to wake their chips from sleep mode. The fault-status (FS, active low) output pins may be left disconnected if you do not want to monitor the fault conditions of the motor drivers; if you do connect them you must use an external pull-up resistor to pull the lines high. IN1 and IN2 control the direction of their associated motor, and D2 can be PWMed to control the motor’s speed. D2 is the “not disabled” line: it disables its motor driver when it is driven low and enables its motor driver when driven high. Whenever D1 or D2 disable a motor driver, that driver’s FS pin will be driven low. Each feedback (FB) pin outputs a voltage proportional to the H-Bridge high-side current of its associated driver, providing approximately 0.59 volts per amp of output current.

 

The dual MC33887 motor driver carrier PCB comes with two 47 uF, 35 V surface-mounted capacitors and holes for installing an additional through-hole capacitor. This third capacitor can be added in conjunction with the two surface-mount capacitors to further limit disturbances on the main power line, or it can be added in place of the two surface-mount capacitors to allow the MC33887 motor driver carrier to function at high voltages.

 

MC33887 Specifications (only one active driver)

  •     - Operating voltage: 5-28 V
  •     - Maximum PWM frequency: 10 kHz
  •     - Current sense: 0.59 V/A
  •     - Time to overheat at 5 A*: 2 s
  •     - Time to overheat at 4 A*: 21 s
  •     - Time to overheat at 3 A*: 165 s
  •     - Current for infinite run time*: 2.5 A

 

*Typical results using the single MC33887 motor driver carrier with 100% duty cycle at room temperature with no forced air flow or heat sink. The dual MC33887 motor driver has a larger PCB and hence will be more effective at drawing heat away from the motor driver chips, but driving two chips simultaneously will generate more heat and could lead to slightly reduced performance.

 

Dimensions
    - Size:1.13" x 1.55"


General specifications
    - Motor driver:MC33887
    - Motor channels:2
    - Minimum operating voltage:5 V
    - Maximum operating voltage:28 V
    - Continuous output current per channel:2.5 A
    - Peak output current per channel:5 A
    - Continuous paralleled output current:5 A
    - Current sense:0.59 V/A
    - Maximum PWM frequency:10 kHz
    - Minimum logic voltage:4.0 V1
    - Maximum logic voltage:5.5 V2
    - Reverse voltage protection?:Y


ไฟล์ดาวน์โหลด: Dual MC33887 Motor Driver Carrier

downloads MC33887 motor driver datasheet : Download
downloads STS25NH3LL MOSFET datasheet : Download

ความคิดเห็นผู้ใช้งาน: Dual MC33887 Motor Driver Carrier

แสดงความคิดเห็น:

เข้าสู่ระบบสมาชิก ก่อนแสดงความคิดเห็น.
รับส่วนลดทันที เพียงแค่คุณแชร์
mce-lab
Foscam
External magnetic Antenna
Cards We Accept เลขทะเบียนพาณิชย์อิเล็กทรอนิกส์