กรณีต้องการติดต่อทางไลน์กรุณาเพิ่มเพื่อนด้วยไลน์ ID : @warf
Advertsement
Arduino Raspberry Pi Zigbee/802.15.4 Sensors Robotics LCDs

ArduPilot Mega - Arduino Mega compatible UAV Controller

2,250.00 THB

ราคาดังกล่าวรวมภาษีมูค่าเพิ่ม 7% เรียบร้อยแล้ว

Facebook Share << คลิ๊ก Share
Part No. : ELE-SP070216240
Manufacture No. : GPS-10294
จำนวนในสต็อก : 1
ต้องการสั่งซื้อจำนวน
OR
ชำระเงิน PayPal แบบใหม่
ช่วยให้คุณซื้อสินค้าได้รวดเร็วและง่ายยิ่งกว่าเดิม
เพิ่มเพื่อน

รายละเอียดสินค้า: ArduPilot Mega - Arduino Mega compatible UAV Controller

The ArduPilot Mega is the newest version of autopilot board designed by Chris Anderson and Jordi Muñoz of DIY Drones. This latest revision uses the ATmega2560 in place of the ATmega1280.

 

ArduPilot Mega is a fully programmable autopilot that requires a GPS module and sensors to create a functioning Unmanned Aerial Vehicle (UAV). The autopilot handles both stabilization and navigation, eliminating the need for a separate stabilization system. It also supports a "fly-by-wire" mode that can stabilize an aircraft when flying manually under RC control, making it easier and safer to fly. The hardware and software are all open source. The board comes with all the surface-mount parts already soldered, but requires the user to solder on connectors. RC processing firmware is already loaded, but the autopilot software must be downloaded and loaded onto the board by the user. It can be programmed with the Arduino IDE.

 

We recommend the following items to accompany this product:

  - uBlox 5 GPS module and adapter
  - FTDI Basic or FTDI cable for programming

 

Other necessary elements, including aircraft recommendations, can be found at the project's home page.

 


Features:
  - Controller designed to be used with autonomous aircraft, car or boat.
  - Based on a 16MHz Atmega2560 processor.
  - Built-in hardware failsafe that uses a separate circuit (multiplexer chip and ATMega328 processor) to transfer control from the RC system to the autopilot and back again. Includes ability to reboot the main processor in mid-flight
  - Dual-processor design with 32 MIPS of onboard power
  - Supports of 3D waypoints and mission commands (limited only by memory)
  - Comes with a 6-pin GPS connector (EM406 style).
  - Has 16 spare analog inputs (with ADC on each) and 40 spare digital input/outputs to add additional sensors
  - Four dedicated serial ports for two-way telemetry (using optional XBee modules) and expansion
  - Can be powered by either the RC receiver or a separate battery
  - Hardware-driven servo control, which means less processor overhead, tighter response and no jitters
  - Eight RC channels (including the autopilot on/off channel) can be processed by the autopilot. 
  - LEDs for power, failsafe status, autopilot status and GPS lock
  - Full autopilot software, including IMU and groundstation/mission planning code,  are available at DIY Drones. Code supports autonomous takeoff and landing.
  - Dimensions: 40mm x 69mm

ไฟล์ดาวน์โหลด: ArduPilot Mega - Arduino Mega compatible UAV Controller

downloads Schematic : Download

ความคิดเห็นผู้ใช้งาน: ArduPilot Mega - Arduino Mega compatible UAV Controller

แสดงความคิดเห็น:

เข้าสู่ระบบสมาชิก ก่อนแสดงความคิดเห็น.
ได้รับการรับรองธุรกิจพาณิชย์อิเล็กทรอนิคส์
mce-lab
How to pay
Cards We Accept เลขทะเบียนพาณิชย์อิเล็กทรอนิกส์